Bulk FaceWear Roll
The only Strapless and Anti-fog FaceWear!
Now available in a commercial sized Bulk Roll!
Our FaceWear can now be conveniently installed in your facility. A bulk roll of SpiderTech FaceWear can fit in any universal 4" dispenser with a 3" core. Employees, customers, visitors can simply tear off one for use and with the continuous roll, the next FaceWear is ready to go.
The bulk roll contains 250 strapless FaceWear. Dispenser not included.
These come pre-cut with a shield pre-installed. As with all SpiderTech tape, the fabric is designed to mimic human skin allowing for a comfortable, flexible fit that conforms to unique features of the face while maintaining a seal around the nose and mouth for as long as you need it.
Just snap, stick and go!
- This is a non-medical mask
- Dispenser not included
- Wax paper shield
- Strapless comfort
- Anti-fog for eyewear
- 100% poly-acrylic adhesive
Product Measurement (Width x Length)
10cm x 23cm
4" x 9"
How to Apply
How to Adjust
How to Remove
How many masks are on each roll?
The SpiderTech bulk roll contains 250 face masks
What size is the core?
The core size is 3 inches.
Is the dispenser included?
No, we will be offering pre-loaded dispenser options at a later date
Can you adjust the stickiness of the glue?
Yes you can do this in two ways:
1) Trim around the SpiderTech FaceWear to lessen the adhesive area. Just make sure not to cut through the center liner.
2) Simply touch the glue in the area where you want less adhesion. Note that the glue loses its strength the more you touch it. It reacts differently on all skin as some skin is dry, some oily, some with makeup, etc.
How do you remove the FaceWear?
When removing the FaceWear, start in the upper right or left corner. With one hand, pull your exposed skin beside the mask towards your ear, tightening your skin. With the other hand, gently roll the corner of the mask down and in towards your mouth. Repeat on the opposite side and then gently roll the mask down the bridge of your nose.
Can the face mask be worn with facial hair?
Our FaceWear is great for people with facial hair; because the bottom strip of filter paper can remain attached covering the adhesive, you can wear it like a face shield and avoid uncomfortable pressure on your facial hair.
How long can you wear the mask for?
The FaceWear can be worn the entire day. It can be removed and reapplied. Just note that every time you remove the mask, the adhesive will lose some strength. If you take it off for longer than 10 minutes, we suggest you re-apply a new FaceWear.
Are the masks reusable and can it be washed?
The FaceWear is for one time use and is disposable. It is not washable or reusable.
What is the shield made of?
The droplet shield in our FaceWear is the backing paper of our kinesiology tape. The backing is a wax paper that works exceptionally well shielding droplets and particles. The mask has been independently lab tested and proved to have a Bacterial Filtration Efficiency of over 99%.
How does it compare with the N95 mask?
SpiderTech FaceWear is a different type of mask and as a result can not be compared to a N95 or other respirator masks. Our FaceWear acts like a shield over your nose and mouth providing an effective protective barrier. Respirator masks effectively filter the air as it comes into the mask.
What if I find it hard to breathe in the mask?
The FaceWear provides the option to seal the bottom of the mask or to leave it open allowing it to act like a face shield. The face shield option provides excellent protection and breathes even easier than the fully sealed option.
What if the adhesive irritates my Skin?
SpiderTech uses a high quality acrylic, hypoallergenic adhesive designed to be worn on sensitive facial skin, however, a low percentage of people will still experience a sensitivity reaction. If you are one of the people who has a reaction to the adhesive, please remove the mask immediately; unfortunately the SpiderTech FaceWear isn’t for you.